Rotary Torque Sensors ---Didital

电      话：0532-85766366  

                0532-85762377

 传真号码：0532-85762366

 节假日联系：13963933390

 

 公司地址：青岛市市南区银川西路3号政泰商务楼211室

 Email：

 chinadongdu@163.com

 

 邮编：266000

 

 公司网址：

 http://www.chinadongdu.cn

 

 http://www.dongduchina.cn

诚信通网址

SETECH

Dacell 韩国大拿

LEBOW

首页 >>> 产品目录 >>> 美国Himmelstein扭矩传感器 >>> Rotary Torque Sensors ---Didital

更详细的产品分类

产品图片	产品名称/型号	产品简单介绍
	美国Himmelstein扭矩传感器 87000v	MCRT® 87000V Torque Transducers output shaft torque with 0.01% resolution. Digital, Analog and FM formats are simultaneously available. Industries highest overload and overrange ratings assure safety and accuracy even when the driveline has high peak to average torque ratios. Important features include non-critical installation, temperature data, max/min capture and absence of manual adjustments. Range, scaling, calibration and null data are stored in rotor nonvolatile memory and transferred to the stator during startup. That assures accuracy, without re-calibration, if rotors and stators are replaced or intermixed. Bi-polar, rotor shunt cal can be enabled with stator switches, logic I/O or, via the Com Port. Choose from ten units of measure without re-calibrating. When you re-calibrate, earlier calibrations are archived. Eleven selectable Bessel data filters avoid overshoot errors and delay distortion. Multiple bridges sense torque and provide immunity to extraneous loads. The radial torque path yields short length, unsurpassed torsional stiffness and deflection resulting in the highest installed system response. The torquemeter attaches to your drive without an additional coupling. The result is low overhung moment, short length and minimal installed space. Himmelstein has made similar, radial path sensors for decades including automotive torque wheels, pulley torquemeters and chassis roll torque sensors. The sensors’ output is digitized on the rotor and then sent to the stator where analog, frequency and Com Port outputs are created. Choose RS232, RS422, or RS485 communications. Included software interfaces with your Windows-based PC. It displays real time data, does time plots and stores test results. Password protection may be invoked. Exceptional Immunity To Noise And Interference From ISM Transmitters To achieve short length, high stiffness and wide signal bandwidth, bearingless sensors use unshielded antennae. As a result, any device (including a like t
	美国Himmelstein扭矩传感器 86000v	MCRT®86000V Torque Transducers output shaft torque with 0.01% resolution. Digital, Analog and FM formats are simultaneously available. Industries highest overload and overrange ratings assure safety and accuracy even when the driveline has high peak to average torque ratios. Important features include non-critical installation, temperature data, max/min capture and absence of manual adjustments. Range, scaling, calibration and null data are stored in rotor nonvolatile memory and transferred to the stator during startup. That assures accuracy, without re-calibration, if rotors and stators are replaced or intermixed. Bi-polar, rotor shunt cal can be enabled with stator switches, logic I/O or, via the Com Port. Choose from ten units of measure without re-calibrating. When you re-calibrate, earlier calibrations are archived. Eleven selectable Bessel data filters avoid overshoot errors and delay distortion. Multiple bridges sense torque and provide immunity to extraneous loads. The radial torque path yields short length, unsurpassed torsional stiffness and deflection resulting in the highest installed system response. The torquemeter attaches to your drive without an additional coupling. The result is low overhung moment, short length and minimal installed space. Himmelstein has made similar, radial path sensors for decades including automotive torque wheels, pulley torquemeters and chassis roll torque sensors. The sensors’ output is digitized on the rotor and then sent to the stator where analog, frequency and Com Port outputs are created. Choose RS232, RS422, or RS485 communications. Included software interfaces with your Windows-based PC. It displays real time data, does time plots and stores test results. Password protection may be invoked. Exceptional Immunity To Noise And Interference From ISM Transmitters To achieve short length, high stiffness and wide signal bandwidth, bearingless sensors use unshielded antennae. As a result, any device (including a like to
	美国Himmelstein扭矩传感器 79700v	The MCRT® 79700V Series of Dual Range Digital Torque Transducers will accurately measure low running and high load torque without the cost and inconvenience of swapping two or more conventional torque sensors. Another important application is measuring torque when the ratio of peak torque to average torque is high. In that situation, a conventional torquemeter must be oversized to avoid damage – a process which greatly reduces accuracy. Conditions that create high peak to average ratios include starting, stopping or reversing inertial loads, torsional oscillations, and diesel and single cylinder engine/compressor drives. Additionally, when peak torques are unknown, an MCRT® 79700V reduces the risk of damage from unexpected or accidental torque spikes. These Dual Range Torquemeters have a LOW range that is 20% of its' HIGH range. Three simultaneous analog outputs can be individually set to 5 or 10 volts at each range full scale. Overrange is 150% to 300% and mechanical overload is 200% of the HIGH range and 1,000% of the LOW range. Digital output of torque, and speed and power with option Z, is available over the resident RS232 serial port. Included software interfaces with Windows based PC's for data display and collection as well as instrument setup. Each range is calibrated in our accredited laboratory and documented by a NVLAP approved calibration certificate certifying NIST traceability and documenting our laboratory operation and our quality management system meets ISO/IEC 17025-2005. Temperature compensation and CW and CCW dead weight load calibrations are performed on each range.
	美国Himmelstein扭矩传感器 59700v	These strain gage torquemeters measure and output shaft torque in analog and digital form. They are available in torque ranges from 40 to 735,000 lbf-in with 10X overload rating. A zero velocity speed option adds analog and digital outputs of speed and computed shaft power. Null, scaling and units of measure are stored in non-volatile memory. There are no noisy pots or switches. Thirty three units of measure are supported without requiring recalibration. Eleven user selectable Bessel filters avoid delay distortion and overshoot errors. These models incorporate new technology that hardens them to EMI generated by IGBT based adjustable speed drives. Included software interfaces Windows-based PC’s and displays and plots real time data. Use it to select 5V or 10V analog outputs, filters, scaling, units of measure and/or to control measurements.
	美国Himmelstein扭矩传感器 49700v	These strain gage torquemeters measure and output shaft torque in analog and digital form. They are available in torque ranges from 25 to 2,000,000 lbf-in with 4X overload rating. A zero velocity speed option adds analog and digital outputs of speed and computed shaft power. Null, scaling and units of measure are stored in non-volatile memory. There are no noisy pots or switches. Thirty three units of measure are supported without requiring recalibration. Eleven user selectable Bessel filters avoid delay distortion and overshoot errors. These models incorporate new technology that hardens them to EMI generated by IGBT based adjustable speed drives. Included software interfaces Windows-based PC’s and displays and plots real time data. Use it to select 5V or 10V analog outputs, filters, scaling, units of measure and/or to control measurements.
	美国Himmelstein扭矩传感器 48700v	These strain gage torquemeters measure and output shaft torque in analog and digital form. They are available in torque ranges from 25 to 4,000,000 lbf-in with 2X overload rating. A zero velocity speed option adds analog and digital outputs of speed and computed shaft power. Null, scaling and units of measure are stored in non-volatile memory. There are no noisy pots or switches. Thirty three units of measure are supported without requiring recalibration. Eleven user selectable Bessel filters avoid delay distortion and overshoot errors. These models incorporate new technology that hardens them to EMI generated by IGBT based adjustable speed drives. Included software interfaces Windows-based PC’s and displays and plots real time data. Use it to select 5V or 10V analog outputs, filters, scaling, units of measure and/or to control measurements.
	美国Himmelstein 扭矩传感器 48200v	These Compact Digital Torque Transducers have high accuracy, low noise, high overload capacity, high overrange, inherent noise tolerance and a wide temperature range. Strain gage sensing and non-contact signal transfer make them well suited for control, laboratory and production use. They are offered in two accuracy grades, Code N standard performance and Code C enhanced performance. Installation can be either floating or foot mounted with the integral mounting base. Null, scaling and units of measure are stored in non-volatile memory. There are no noisy pots or switches. Ten common units of measure are supported without requiring recalibration. Eleven user selectable Bessel filters avoid delay distortion and overshoot errors. Included software interfaces Windows-based PC's and displays and plots real time data. Use it to select ±5V or ±10V analog outputs, filters, scaling, units of measure and/or to control measurements.

青岛大镎东都测控技术有限公司电话：0532-85762377 0532-85766366 传真：0532-85762366
地址：青岛市市南区银川西路3号政泰商务 211 邮编：266000 鲁ICP备09028942号-1 网站管理入口

网络推广：仪表展览网

技术支持：易展